In order to send passive beacon-requests, channel and op-class of nodes
are required. Obtain this information per local-node from hostapd.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently the min_snr option will result in kicking clients the first
time their SNR dips below.
This might not be desirable, as drivers (notably ath10k) sometimes
report a much lower RSSI for a short timeframe after returning to
sensible values. Also, a device might be in the process of roaming just
to be kicked before.
Add the min_snr_kick_delay option. A client will be kicked after this
timeframe when it's SNR is below the min_snr threshold value over the
complete timeframe.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make usteer handle incoming BSS-transition requests. Update with the
most active roaming neighbors like we already do for imminent
disassociations.
Create a new ubus method which calls hostapds bss_transition_request
method. This does not set the disassoc imminent bit, thus will not
automatically disassoc the requesting STA.
Signed-off-by: David Bauer <mail@david-bauer.net>
Don't determine a finished client scan based on whether the current node
has seen a beacon or not.
This works surprisingly bad on 5 GHz nodes, as clients may refuse to
perform active scanning on this frequency band. In case the clients does
refuse to scan the 5 GHz band but scans the 2.4 GHz band actively, we
might have a good indication about a better node on this band at least.
However, as the roam state-machine requires to have seen a probe request
from the client to direct him to a better node, thi process will not
continue, which either ends the node in being kicked due to exceeding
the number of max tries or the scan cooldown to kick in.
The solution to this is fairly simple: Don't track the roam_scan_done
state but instead just determine a better candidate after the scan
interval finished.
To ensure the indicated signal levels are as recent as 2 *
scan-interval, add a max_age parameter to find_better_candidate.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add an optional timeout when a better roaming candidate is not found
after the scan-retry limit. The roam state-machine will not retry
scanning before this timeout has expired.
If the timeout is set to 0, the client is kicked instead, which
resembles the behavior prior this commit.
This is added, as without this patch, if a forced disconnect
is not desired before roam_scan_trigger is exceeded the client will
repeatedly be asked to return active beacon-reports. For battery powered
clients this can result in a noticeable battery drain.
Signed-off-by: David Bauer <mail@david-bauer.net>
Export snr_to_signal to other source files. This will be necessary to
determine reported signal strengths from beacon-report throughout the
code base.
Signed-off-by: David Bauer <mail@david-bauer.net>
Logic for handling STA transition to disconnected state is
present multiple times. Create a new method to remove
duplicate code.
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the roam event counters to a dedicated struct.
Update the ubus output to represent this new organization.
Signed-off-by: David Bauer <mail@david-bauer.net>
Don't request measurements from STAs which do not support the specific
measurement mode. Otherwise, hostapd complains in the syslog about
unsupported measurement modes.
Signed-off-by: David Bauer <mail@david-bauer.net>
Save the RRM capabilities of STAs when updating clients from hostapd.
This is required to determine which measurement modes a STA supports.
Signed-off-by: David Bauer <mail@david-bauer.net>
Save the timestamp of the node creation. This is required to optimize
the selection of most-roamed to neighbors relative to their creation
time.
Signed-off-by: David Bauer <mail@david-bauer.net>
Prioritize neighbor candidates installed to hostapd. Add a new config
option to set a limit for neighbor reports installed to hostapd. This is
due to the fact, most devices will only evaluate a certain amount of
neighbor reports. Furthermore, the number of neighbor reports possible
is limited by the maximum frame size.
Signed-off-by: David Bauer <mail@david-bauer.net>
Keep track of STA journeys between multiple nodes. When a new STA is
reported from a foreign node, check whether this STA was previously
associated with a local node.
Vice versa, check upon association whether or not the STA was previously
associated with a foreign node.
Keep track of these roaming transactions using two new (local) fields of
the node struct.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a last_connected field to the sta_info struct. This field can be
used to determine, if and when a client was last connected to a given
node. This way, other nodes can determine where a client roamed to or
from.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make the connection state of a sta-info more readable by introducing an
enum for the STA connection state.
Also switch come comparison cases to use the explicit enum values to
make the code more readable.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the node BSSID to the usteer_node struct. This will be helpful in
the future when evaluating beacon reports from STAs.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds optional support for message exchange using IPv6 multicast
messaging. This has the ability for routers and switches between nodes
to route traffic between usteer nodes multicast-aware.
By default, IPv4 is used. IPv6 can be enabled by configuring the ipv6
option to 1.
Signed-off-by: Jan Braun <keksgesicht23@gmail.com>
[squash commits - adapt usock usage]
Signed-off-by: David Bauer <mail@david-bauer.net>
- make logging events more structured
- add fine grained control over log events
- make it possible to receive more detailed events via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
